How to set up your Ping Lifestyle Outdoor table
In order to assemble your outdoor lifestyle ping pong table, please refer to the explanations below. A minimum of two people is required at all stages to assemble your table. All the tools you will need to assemble your Lifestyle table are provided: a 10 mm socket spanner, a 13 mm open-end spanner, a 4 mm Allen key and a PZ 2 screwdriver. The use of a screwdriver is not recommended as it could damage some parts, rendering them unusable. Rackets and balls are also supplied with your table.
Before assembly
Cut out the side of each of the two boxes. You can use the cardboard boxes as a support when assembling your table. They will effectively protect the various parts and your floor from scratches.
BEFORE ASSEMBLY
Cut out the side of each of the two boxes. You can use the cardboard boxes as a support when assembling your table. They will effectively protect the various parts and your floor from scratches.
Step 1
Insert one of the two splice bars (Part No. 7241.R) into the right bottom rail (Part No. 7250) and repeat this step with the left bottom rail.
Step 1
Insert one of the two splice bars (Part No. 7241.R) into the right bottom rail (Part No. 7250) and repeat this step with the left bottom rail.
Step 2
Provide yourself with two screws (part number 1720.0) and, at the location shown in the diagram, screw them in lightly by hand, repeating the step on the two previously mounted parts.
Step 2
Provide yourself with two screws (part number 1720.0) and, at the location shown in the diagram, screw them in lightly by hand, repeating the step on the two previously mounted parts.
Step 3
Take the second bottom rail (part number 7251) and place it on the other end of the splice bar. Repeat this step with the second spar.
Step 3
Take the second bottom rail (part number 7251) and place it on the other end of the splice bar. Repeat this step with the second spar.
Step 4
As in step 2, lightly hand-screw a screw (part number 1720.0) to the end of the part. Repeat this step with the second spar as well.
Step 4
As in step 2, lightly hand-screw a screw (part number 1720.0) to the end of the part. Repeat this step with the second spar as well.
Step 5
Place the two assembled parts vertically and lightly hand-screw the centre crossbar (part number 7244) into the centre of these two parts, as shown in the video.
Step 5
Place the two assembled parts vertically and lightly hand-screw the centre crossbar (part number 7244) into the centre of these two parts, as shown in the video.
Step 6
Place the centre bracket (item no. 7240) with its legs up between the two plates and provide three washers (item no. 1210.0), three nuts (item no. 1124.0) and three screws (item no. 1719.0). As shown in the diagram, securely fasten the three pieces together using the socket spanner and the Allen key.
Step 6
Place the centre bracket (item no. 7240) with its legs up between the two plates and provide three washers (item no. 1210.0), three nuts (item no. 1124.0) and three screws (item no. 1719.0). As shown in the diagram, securely fasten the three pieces together using the socket spanner and the Allen key.
Step 7
Assemble the assembly previously made in steps 1 to 5 with the table tops as shown in the diagram opposite, using screws (part number 1720.0) and nuts (part number 1124). Tighten lightly by hand. Repeat this step on the left and right.
Step 7
Assemble the assembly previously made in steps 1 to 5 with the table tops as shown in the diagram opposite, using screws (part number 1720.0) and nuts (part number 1124). Tighten lightly by hand. Repeat this step on the left and right.
Step 8
Hand-tighten the right and left sleeves (item no. 7247 and 7248) to the table tops on both sides of the table using eight washers (item no. 1210.0), eight lock nuts (item no. 1120.0) and eight screws (item no. 1720.0).
Step 8
Hand-tighten the right and left sleeves (item no. 7247 and 7248) to the table tops on both sides of the table using eight washers (item no. 1210.0), eight lock nuts (item no. 1120.0) and eight screws (item no. 1720.0).
Step 9
Attach the four struts to the four corners of the table with sheet metal screws (part number 1370) using the screwdriver provided. As in the video, slide the struts between the sleeves and the stringers.
Step 9
Attach the four struts to the four corners of the table with sheet metal screws (part number 1370) using the screwdriver provided. As in the video, slide the struts between the sleeves and the stringers.
Step 10
Take the legs (item no. 8609) and four skate screws (item no. 2215) and screw them in gently as shown in the diagram using the flat spanner supplied. Repeat the step with the other three legs.
Step 10
Take the legs (item no. 8609) and four skate screws (item no. 2215) and screw them in gently as shown in the diagram using the flat spanner supplied. Repeat the step with the other three legs.
Step 11
Take the skid (part number 4821), place it on the floor and push in the ball screw until you hear a "click". Repeat the step with the other three feet.
Step 11
Take the skid (part number 4821), place it on the floor and push in the ball screw until you hear a "click". Repeat the step with the other three feet.
Step 12
Glue the anti-skid pad (part number 4825) to the skid. Repeat this step on the other three feet.
Step 12
Glue the anti-skid pad (part number 4825) to the skid. Repeat this step on the other three feet.
Step 13
Slide the four feet into the sleeves.
Step 13
Slide the four feet into the sleeves.
Step 14
Provide yourself with sixteen washers (order no. 1210.0), eight nuts (order no. 1120.0) and eight screws (order no. 1728.0) and, as in the video, attach the side rail, strut, leg and leg crossbar together. Repeat this step for each leg.
Step 14
Provide yourself with sixteen washers (order no. 1210.0), eight nuts (order no. 1120.0) and eight screws (order no. 1728.0) and, as in the video, attach the side rail, strut, leg and leg crossbar together. Repeat this step for each leg.
Step 15
Using the tools provided, tighten each screw previously placed by hand.
Step 15
Using the tools provided, tighten each screw previously placed by hand.
Step 16
Slide the drawer rail into the drawer and screw it in place as shown with two sheet metal screws (order no. 1370).
Step 16
Slide the drawer rail into the drawer and screw it in place as shown with two sheet metal screws (order no. 1370).
Step 17
Push the plugs (Part No. 4320) into each end of the drawer rail.
Step 17
Push the plugs (Part No. 4320) into each end of the drawer rail.
Step 18
Slide the ends of the drawer one after the other into place on the reinforcing bars. You can install the drawer on either side of the table. A second drawer is available as an option.
Step 18
Slide the ends of the drawer one after the other into place on the reinforcing bars. You can install the drawer on either side of the table. A second drawer is available as an option.
Step 19
Screw the drawer in place as shown in the diagram with two sheet metal screws (order no. 1370).
Step 19
Screw the drawer in place as shown in the diagram with two sheet metal screws (order no. 1370).
Step 20
Munissez vous d'un tournevis PZ2, de deux vis (référence 1601), deux éclisse (référence 4775.0), deux rondelles grower (référence 1256) et deux écrous papillon (référence 1163). Afin de fixer le système d'accroche de votre filet. Respectez bien l'ordre, comme indiqué sur le schéma. Vissez l'ensemble solidement sur les barres de renfort en Aluzinc© se trouvant entre les plateaux et les longerons préalablement installés.
Step 20
Munissez vous d'un tournevis PZ2, de deux vis (référence 1601), deux éclisse (référence 4775.0), deux rondelles grower (référence 1256) et deux écrous papillon (référence 1163). Afin de fixer le système d'accroche de votre filet. Respectez bien l'ordre, comme indiqué sur le schéma. Vissez l'ensemble solidement sur les barres de renfort en Aluzinc© se trouvant entre les plateaux et les longerons préalablement installés.
Step 21
Turn the table over. Please note that more than two people may be required to lift the table (76kg).
Step 21
Turn the table over. Please note that more than two people may be required to lift the table (76kg).
Step 22
Place the thread bases (art. no. 4820.A) on the central bracket in the middle of the table, place the thread on it and press down to lock it.
Step 22
Place the thread bases (art. no. 4820.A) on the central bracket in the middle of the table, place the thread on it and press down to lock it.
Rangement du filet
To store the net, place it parallel to the table, notch one side first and then the other, as in the video.
Rangement du filet
To store the net, place it parallel to the table, notch one side first and then the other, as in the video.
